BREAKING

Tech Tips/ DIY

Bar Swappin’ – Sportster Handle Bar And Grip Swapping

Article & Photos By: Lowbrow Customs – www.lowbrowcustoms.com

Originally Published In The June 2016 Issue Of Cycle Source Magazine

csm-june2016-pg18_page_1_image_0001

Swapping out the handlebars and grips on your motorcycle makes a big change visually as well as in handling. This step-by-step article will walk you through the process and ensure that you are completely comfortable in the knowledge that you can tackle this project in less than an hour and be back on the road.

csm-june2016-pg18_page_1_image_0002

TOOLS NEEDED: 3/8 drive ratchet, 1/4 ratchet, 1/4 Allen socket, T25 and T27 torx bit, 3/4 wrench or socket

csm-june2016-pg18_page_1_image_0003

A towel or rag over your gas tank is cheap insurance to protect against a dropped tool or fastener!

csm-june2016-pg18_page_1_image_0004

Remove the two allen bolts holding your speedometer mount in place, and carefully drop it forward out of the way onto your headlight (which you can also protect with a rag)

csm-june2016-pg19_page_1_image_0002

Loosen the two screws holding your clutch lever perch in place using a T27 torx driver and remove the clutch from the handlebars.

csm-june2016-pg19_page_1_image_0003

Using the T25 torx driver, loosen the two screws holding your left-hand switch pod in place. If you don’t plan to reuse it, the left-hand grip can easily be removed by carefully cutting through it with a razor blade and peeling it off of the handlebar.

csm-june2016-pg19_page_1_image_0004

Using your T27 torx driver, remove the two screws holding your front brake lever in place and remove it from the handlebars. Loosen the two screws on your throttle assembly using T25 torx so you can slide the throttle off of the end of the bars and out of the way

csm-june2016-pg19_page_1_image_0005

Now that the controls are all removed, you can remove the final two allen bolts holding the top clamp to the risers and remove the old handlebars.

csm-june2016-pg19_page_1_image_0006

Take your time to center your handlebars in your risers. Install the top clamp tight enough to hold the bars upright, but loose enough so you can adjust the angle of the handlebars while sitting on your motorcycle.

csm-june2016-pg19_page_1_image_0007

Once you have them positioned how you like them, replace your speedometer bracket and tighten all four allen bolts holding your top clamp in place.

csm-june2016-pg19_page_1_image_0008

Time to swap the grips. Remove the screws holding your throttle assembly together so it exposes the end of the throttle cables and throttle tube.

csm-june2016-pg19_page_1_image_0009

Loosen your cable adjusters with two wrenches and thread them in further to give you slack in your cables. This will allow you to remove the cable ferrules (ends) from the plastic throttle tube.

csm-june2016-pg19_page_1_image_0010

You can use a razor blade to slit the old grip on your throttle tube and peel it back if you are not going to save

csm-june2016-pg20_page_1_image_0001

the old grips.

csm-june2016-pg20_page_1_image_0002

Note that motorcycle grips have two different I.D.s (inside diameters).

csm-june2016-pg20_page_1_image_0003

Using some WD-40 as lubricant, slide the smaller I.D. grip onto the left side of the handlebar.

csm-june2016-pg20_page_1_image_0004

The larger I.D. grip is made to go over the throttle tube, which also benefits from the application of WD-40 to make the install easier. You can also use compressed air by sticking the tip of your air nozzle under the grip and spraying air while pushing on the end of the grip.

csm-june2016-pg20_page_1_image_0005

Reverse the disassembly. Slip the throttle tube over your bars and install the throttle cable ferrules into position and be sure to readjust your throttle cables. Install the throttle housing, switch housings, clutch lever and brake lever.

csm-june2016-pg20_page_1_image_0006

Be sure to check that all hardware is tight before taking it for a test ride to check out your new riding position and style!

Related Posts

1 of 33