Working Man’s Build – Part 2

Customizing Jared Blake’s Sporty with Pandemonium Custom Choppers

Article and Photos By: Daniel Donley – www.pandemoniumcustomchoppers.com

Originally Published In The July 2016 Issue Of Cycle Source Magazine

CSM-JULY2016.pg66_Page_1_Image_0001

Just to recap on last months beginning of this article, I recently was approached by Jared Blake, He is hard working country music singer, out there pounding the pavement to make a living, just like you and I do every day. After a summer tour from one bike event to another and seeing all of the cool bikes. He thought that his stock looking sportster back home, wasn’t so cool anymore and needed an update. But just like any hardworking American, money is hard to come by sometimes. So with this project we are on a budget, which doesn’t mean we can’t have the max cool for the least money. So the plan is to give this plain jane some soul…..

CSM-JULY2016.pg66_Page_1_Image_0002

This is where we left off last month with the Jared Blake working man’s build. We got a lot of work done in a short weekends time, now let’s get this project all wrapped up.

CSM-JULY2016.pg66_Page_1_Image_0003

A few too many miles or maybe a few too many burnouts this ol’ girl was in need of some new shoes. So we are going to put some new tires on.

CSM-JULY2016.pg66_Page_1_Image_0004

Out with the old bologna rinds and in with some stylin’ and profilin’ white wall shoes! It’s also always good practice to check your bearings and races for wear. Also you need to re-grease your bearings and check bearing end play. Which should be .002 to .006. Don’t forget to install new wheel bearing seals.

CSM-JULY2016.pg66_Page_1_Image_0005

Since Jared’s bike has a lot of Chrome the black pulley looked really out of place and to keep it cost effective we installed a chrome pulley cover. To give the rear wheel the pizazz it needed.

CSM-JULY2016.pg66_Page_1_Image_0006

The front got the same stylin’ and profilin’ white wall as the back!

CSM-JULY2016.pg67_Page_1_Image_0002

The rear brake pads were shot so new ones were in order

CSM-JULY2016.pg67_Page_1_Image_0003

Both rear shocks were leaking and had no dampening, to make sure Jared has some cushion from the bad roads and to get the low aggressive look a set of 10 ½” Burly Slammer shocks were in order.

CSM-JULY2016.pg67_Page_1_Image_0004

CSM-JULY2016.pg67_Page_1_Image_0005

Before and after, sometimes all it takes is the simple removal of some “doodad” that somebody else wasted their money on. No more headlight brow!

CSM-JULY2016.pg67_Page_1_Image_0006

The derby cover was leaking and needed resealed. Another “doodad” was removed in the process. We decided to go with a simple chrome derby cover.

CSM-JULY2016.pg67_Page_1_Image_0008

The old tuna can air filter assembly just wasn’t fittin the bill. We decided to go with a TC Bros cast finned aluminum air filter assembly. This definitely fit the look were after.

CSM-JULY2016.pg67_Page_1_Image_0009

Both the clutch and brake levers were banged up pretty good so we replaced them with some flashy speed hole ones. Also installed a new rearview mirror.

CSM-JULY2016.pg67_Page_1_Image_0010

Visual Impact did a knockout job on the paint, while Visual had the tank we also had him seal the inside.

CSM-JULY2016.pg67_Page_1_Image_0011

CSM-JULY2016.pg67_Page_1_Image_0012

Gas tank and rear fender installed

CSM-JULY2016.pg67_Page_1_Image_0013

CSM-JULY2016.pg67_Page_1_Image_0014

It’s a wrap! On the Working Man’s Build! I had a lot of fun working on this project for Jared Blake. Sometimes keeping things clean and simple is the best way to go. All that is left is to take it for a test ride and then it is off to Jared to enjoy for the summer! Thank you Jared I hope you dig it!

CSM-JULY2016.pg67_Page_1_Image_0015

If there is something that you would like to see me do a Tech article on? Please call me or email me with your idea for a tech article! If you have any questions, please feel free to call me at the shop anytime 419-576-6812 Daniel Donley Pandemonium Custom Choppers info@pandemoniumc2.com

You must be logged in to post a comment Login

Want more information on advertising with Cycle Source in Print or On-line? Email us and we’ll send you info today!